Uwell Caliburn G3 Replacement Pods, 4 Pack, 0.9 Ohm MTL

The Caliburn G3 uses an integrated pod format where the coil mesh is built into the pod body at manufacture. There is no separate coil component to source, handle, or install. When you purchase these pods, you are buying the complete replaceable unit: pod body, e-liquid reservoir, coil, and mouthpiece together.

The replacement process is direct. When you notice a persistent burnt or muted flavour from your current pod (the primary sign that the coil is nearing the end of its life), you remove the old pod from the Caliburn G3, insert a fresh one, fill it via the fill port, allow a short saturation period for the e-liquid to reach the coil, and begin vaping. No priming with dripped e-liquid is required beyond the standard waiting period after filling.

The trade-off with integrated pods compared to modular systems (where you buy a pod body once and replace only the coil) is that the per-coil cost is slightly higher because you are also discarding the pod body each time. For the Caliburn G3, this is offset by the consistent out-of-pack performance of a factory-installed coil: each new pod delivers the same flavour profile at the start as the last, without the variability that can arise from manually seating a coil.

The 0.9 Ohm pod is the in-stock option. At 0.9 Ohm, the Caliburn G3 operates at low wattage and produces a tight mouth-to-lung draw. The restricted airflow and lower vapour volume suit 18 to 20 mg nicotine salt, making this the preferred configuration for vapers switching from cigarettes or those who have settled into a tight MTL vaping style. The 0.9 Ohm pod is the higher-resistance of the two options and delivers the most cigarette-adjacent draw experience the Caliburn G3 offers.

The 0.6 Ohm pod is currently out of stock. At 0.6 Ohm, the device fires at a slightly higher wattage and produces a somewhat more open draw than the 0.9 Ohm. The draw is still within MTL territory but with less restriction and marginally more vapour per pull. Use 12 to 18 mg nicotine salt with the 0.6 Ohm pod when it returns to stock. The reduced restriction compared to the 0.9 Ohm suits vapers who find the tightest MTL draw slightly too constrained but are not ready to move to a fully open DTL setup.

If you are unsure which to start with, the 0.9 Ohm is the recommended entry point for any smoker switching to the Caliburn G3. The tighter draw at 0.9 Ohm most closely matches the physical sensation of a cigarette pull and delivers effective nicotine at 18 to 20 mg salt concentration.

Uwell built the Caliburn reputation on a single thing done well: clean, accurate flavour from a small MTL pod. The G3 carries the Pro-FOCS flavour coil technology that runs through the series, a mesh-and-wick arrangement tuned to present the e-liquid honestly rather than muffling it. In practice that means a fruit reads as the fruit and a dessert keeps its layers, where cheaper pods tend to flatten everything into a generic sweetness.

The integrated mesh also warms evenly across its surface, which is part of why these pods avoid the hot-spot harshness that can creep into worn coils. From the first draw on a fresh pod to the last clean one before it tires, the flavour stays consistent, and the tight 0.9 Ohm airflow concentrates that flavour rather than diluting it with excess air.

This is the reason a lot of vapers stay in the Caliburn ecosystem across generations. Once the flavour bar is set, a noticeably worse pod is hard to go back to, and the G3 pod holds that standard while keeping the simple drop-in-and-vape convenience of an integrated unit.

There is no separate coil to install, so setup is quick, but a fresh pod still needs a moment to wick before the first vape. Skip that and the cotton scorches on the opening draw, which is the most common reason a new pod tastes burnt.